The most affordable and highly functional modern router today is Sagemcom [email protected] 2804v7. Setting up this device using the example of connecting to Rostelecom equipment, its main technical specifications and capabilities will be described within the framework of this material. All this will allow the new owner of such a router to start using it for its intended purpose and with minimal problems.
Briefly about the device
As noted earlier, this device belongs to the series of the most budgetary routers with good technical parameters. On the top side of the case there is one universal USB connector and two dedicated buttons. One of them disables the wireless segment of the computer network, and the second activates WPS technology, with the help of which smartphones or tablets are automatically connected to the router.
The following information LEDs are displayed on the front panel of the case:
The first indicator indicates the presence of power.
The second signal element indicates an active connection using a technology such as ADSL.
The third LED is an indication of receiving information using the Ethernet standard.
The fourth indicator characterizes the operation of the Wi-Fi transmitter.
The last, ninth signal element characterizes the operation of the USB ports.
On the opposite side of the body of the device, wired communications are displayed, which include a power socket, 4 LAN ports, 1 USB connector and 1 ADSL port. There are also power and reset buttons.
There is an information sticker on the bottom of the case. It contains the name of the wireless network (SSID) and password to connect to it. It is better to write this information down on paper right away or remember it for the reason that it may be needed in the process of setting up the Internet. Rostelecom sets individual values for these parameters for each such solution, and this ensures a high level of network security during operation.
The main characteristics of the router
Only in combination with Rostelecom equipment, the Sagemcom router [email protected] 2804 v7 can function. The manufacturer indicates the presence of such parameters for him:
Single-band wireless Wi-Fi signal transceiver that can transmit information at speeds up to 300 Mbps.
Four RJ-45 sockets allow you to fully create the wired part of the computer network. In this case, the speed will decrease and will be 100 Mbps. Also, one of them can act as a WAN input port. That is, it will provide information from the Internet.
Two unified USB ports. They can be used to connect a printer / MFP, and to create a network drive, and to install a 3G modem.
One input ADSL-connector for the implementation of switching with the global web.
Delivery list
The manufacturer equipped this network gateway with the following list of equipment:
The cord is computer, interface, which is crimped with connectors on both sides.
User manual detailing Sagemcom setup [email protected] 2804v7.
A CD with an updated version of the software shell of this network gateway.
One year warranty card.
First step in the setup process: connection
Setting up Sagemcom [email protected] 2804 v7 begins with the right choice of the installation site for this solution and the supply of all necessary communications. That is, it is desirable to position the router in question so that it is as close as possible to the geometric center of the room. This will ensure the maximum quality of WiFi network coverage. The second important circumstance is that all wires should reach the place where the network gateway is installed without problems (this is both the input twisted pair from the provider and the power cable). After choosing the installation site and supplying communications, you must perform the following actions:
We install the power supply in the socket, and we bring its cord to the router and connect the plug from it.
We connect the wire from the equipment of the Rostelecom provider to the ADSL port.
In the 3G modem, we install the SIM card of the cellular operator, and itself in the USB port.
Using the twisted pair cable that is included in the delivery, we switch directly from the PC to the router.
At the final stage, if necessary, we perform all other wired connections.
Router Shell Update
The next step is to run the Sagemcom Setup Wizard [email protected] 2804 v7 from CD. In the window that opens, select the “Update router” item and, following its instructions, update the router shell. By default, this device has an international version of the program v5. And in order for this solution to start functioning successfully with the equipment of Rostelecom, you need version v7, which is recorded on disk. It is this problem that is being solved at this stage.
Reconfiguring program parameters
Next, you need to reconfigure the router software shell. To do this, we launch the setup wizard from the disk and select the “Full setup” item in its autorun menu. Following his instructions, we configure properly and save the values in Sagemcom [email protected] 2804v7. WiFi setup is not required. You can use its default settings.
Backup way to connect to the global web
In this case, the cellular network of any possible operator and a 3G modem act as a backup method for connecting to the global web. Before choosing the latter, it is necessary to clarify its compatibility with the network gateway in question. You will also need a starter pack with a SIM card. Otherwise, the software setting of the Sagemcom modem [email protected] 2804 v7 comes down to performing the following manipulations:
On the computer connected to the network gateway, launch any browser available for use.
In the address bar of the latter, you need to type 192.168.1.1.
Then, in the login window, you need to type the word admin in both fields. This is the login, this is the password.
After that, an interactive interface will open without fail, with the help of which the software parameters of the device in question are configured.
We save the entered values.
Exit the configuration interface.
IPTV activation
The router of the Sagemcom model considered in this material fully supports interactive television technology [email protected] 2804v7. Setting up IPTV consists of the following actions:
In the previously described way, we go into the interactive interface for configuring the network gateway.
Then you need to select the “Additional settings” section in it, and “Interface grouping” in it.
We save the specified parameters and exit the interactive interface.
Testing the health of the network node in question
After that, the Internet setup is completed. Rostelecom, as we see, has greatly simplified the process of performing this operation. Now you need to make sure that the computer network is working. To do this, on any device that is connected to this network gateway, launch the browser and open any test page. You also need to turn on the IPTV set-top box and check it in action.
Price. Users about network gateway
Now Sagemcom router [email protected] 2804 v7 from Rostelecom can be bought at a price of 1100-1200 rubles in a new condition. If you look in the direction of trading platforms where you can buy used computer components, you can reduce the cost to 500-600 rubles.
The owners characterize the considered network node as reliable, affordable, functional. At the same time, no significant shortcomings were found in the process of its use.
Conclusion
As part of this review, the Sagemcom setup was considered in detail and step by step. [email protected] 2804v7. There is nothing super complicated in this operation. And the main merit in this is the specialists of Rostelecom, who simplified the process of its implementation as much as possible.
Router Rostelecom Sagemcom [email protected] 2804 v7 is a branded hardware and software product designed to connect client equipment and mobile devices to the Internet at speeds up to 300 Mb/s. The router is capable of receiving an IPTV signal after appropriate configuration. It is optimized by the manufacturer to work in the network of the largest domestic telecommunications service provider Rostelecom. The device supports ADSL (telephone cable) and Ethernet (four- or eight-core twisted-pair) connections.
The router belongs to the budget series of Rostelecom modems. It is distinguished by high build quality, ergonomic shape, sufficient functional parameters and good technical characteristics. On the upper plane of the case is a USB-3.0 connector and two keys to turn off the wireless connection and activate WPS technology.
In appearance, the device resembles the popular dlink dir 300 model. An information label, which is glued to the bottom surface of the device, tells the SSID and password to enter the router's web interface.
The main characteristics of the router
In addition to the standard network traffic distribution and IPTV signal reception, the model [email protected] 2804 v7 from Sagemcom supports:
- creation of a backup broadband channel;
- the ability to use the device as a print server;
- the ability to perform the functions of a network drive (this will require connecting an HDD or SSD to a router via a universal USB bus, which will turn it into a miniature web server with simultaneous access to data from several client devices).
The router is compatible with the 802.11b/g/n WFA specification and provides full-fledged work with 3G modems. There is a built-in DLNA server. The performance of the central processor is enough to simultaneously process requests from multiple client devices to provide quick access to multimedia content.
You can watch IPTV in FHD quality (1080p). Switching to the Internet is carried out by connecting a telephone cable to the input ADSL connector (asymmetric digital subscriber line) or a twisted pair with an RJ-45 connector to a high-speed WAN port. The device consumes less than 10 W of electricity and has dimensions of 185x110x30 mm (LxWxH).
Delivery list
The standard delivery package of the router includes:
- The device itself.
- Power adapter 12 V.
- Telephone cable with RJ-11 connector.
- Quick User Guide.
- Splitter (signal splitter for telephone and high-frequency modem).
- CD-ROM with proprietary utility - automatic network configuration wizard.
In the box with the router, you can also find a warranty card that has a validity period of 1 year.
Preparing the Sajemcom router
First, you need to supply power to the Rostelecom Sagemcom router. Before setting the router parameters, it is necessary to correctly connect the network card of the computer (discrete or integrated into the system board) with the LAN connector of the device, highlighted in yellow, with a patch cable. In this case, a characteristic click should be heard.
If the connection is made via a telephone cable, then the plug is inserted into the ADSL port. When using Ethernet technology, the connection is made through the WAN connector. If the router is connected via twisted pair, then the LED indicator will turn green, but there will be no access to the Internet without setting access parameters.
Authorization in the web interface
To enter the control panel, you need to launch a browser on your computer and enter the device's IP address: 192.168.1.1. These are the factory default settings. An authorization window will appear. It enters the password admin. The username is the same. The login/password pair can be changed in the security settings of the web interface.
Router Shell Update
The firmware is updated using the CD included in the package. This will ensure the correct operation of the device and support for all functions. If the operating system is configured to automatically launch programs from removable media, then the welcome window of the Rostelecom Hardware Configuration Wizard will immediately appear on the screen. Otherwise, you need to activate the utility manually by double-clicking on the executable file. Set the marker in the dialog box that opens to "Update the universal router" and click "Next".
Removing unnecessary factory connections
The router by default creates initial unhealthy connections. They must be removed, which will avoid errors in the operation of the device. To do this, the following step-by-step algorithm of actions is performed:
The window will then refresh again. We press the last line of the menu with the name "ETH Interface". The page will reload again and the factory configuration will disappear.
Automatic installation of the Sajemcom 2804 router using the hardware setup wizard
In the main window of the configuration wizard, select the item "Full configuration of the universal router" and click the "Next" button. It remains only to wait for the end of the procedure, during which the following operations are carried out:
- The optimal router configuration is selected.
- The required PPPoE connection parameters are set.
- A separate channel for 3G is reserved.
- The availability of the provider's equipment and the compatibility of the subscriber device with it are diagnosed.
- VCI and VPI values are set.
When the configuration of the Rostelecom Sagemcom router is completed, click the "Apply" button and reboot the equipment.
How to set up a fast 2804 v7 router manually
The router and network adapter of the computer can be configured independently. Such a need arises in the absence of an installation disk. This method is also suitable for experienced users who prefer to do everything by hand. Configuring adapter settings on Windows 10 is similar to this procedure in other OS versions developed by Microsoft.
The Sajemcom fast 2804 router supports several options for connecting to the Internet:
- ADSL.
- High-speed fiber optic cable using FTTB technology.
- Building a home wireless network.
- Work in print server mode.
The functionality of the model includes receiving an IPTV signal, which can be configured manually with an individual setting of the desired parameters.
Ethernet connection
To configure an Ethernet connection in the web interface of the router, you need to click on "Advanced settings", go to the ETH service, select the "eth0/eth0" item and set it to "VLAN/MUX". When exiting, save the changes by clicking on the appropriate button at the bottom of the window. We go to the "WAN service", click "Add" and select the "eth0 / eth0" parameter in the list that appears.
On the next page, we assign the value "-1" to the PPPoE connection by writing it in the two fields below. We press "Next". Here we enter the login and password from the contract with the provider. We mark "Enable NAT" and "Firewall". We skip the following pages by clicking the “Next” button everywhere. When you exit the setup wizard, save your changes.
Wireless network in the router
The model supports all existing wireless standards and allows you to create multiple guest connections. Wi-Fi settings are set in the "WLAN" section of the advanced settings of the router's control panel. Here you can enable IGMP - a special multicast protocol. To activate the Wi-Fi module, in the first section of the WLAN settings menu, check the box "Enable wireless communication".
How to set up with an ADSL connection
An Internet connection using ADSL technology is established in the "ATM PVC Interface" section of the WAN service. Here is the automatically created connection PVC 8/32. It must be removed by first ticking it. By pressing the "Add" button, we create our own connection and specify the VPI / VCI parameter - "0/33" by entering it in the field located next to it. Set the DSL Link to "EoA" and the encapsulation to LLC. After completing the basic settings, restart the router.
To set the necessary parameters of the 3G modem, you need to connect it to the router via a USB port. The setup algorithm is as follows:
- In the router control panel, select the "3G Configuration" section.
- Set the marker to "Enable 3G reservation".
- We save the changes made.
With these settings, the device will turn on 3G if an ADSL or Ethernet connection is not available. IPTV does not function in this mode.
Setting up a router to work with a TV set-top box
To activate and configure IPTV, follow these steps:
- In the "Layer 2 interface" section of the router's control panel, open another communication channel.
- Create a new object in the WAN service.
- Set the connection type to "Bridge".
- Apply the changes.
After that, in the LAN settings, check the box next to "Turn off the DHCP server" (a technology developed by Sony to protect digital content from illegal copying and distribution). Then enable "IGMP Shopping" and "IGMP Proxy".
Possible problems
When setting up a Sagemcom router [email protected] 2804 v7 sometimes has technical issues. In this case, the network link indicator, marked with an "@" sign, glows red, and a message appears on the computer screen stating that the router is not found or is not available.
Fixed by switching the patch cable to another LAN port. Router identification errors are possible due to the lack of factory settings. In this case, you will have to prescribe all the necessary values \u200b\u200bmanually. To correctly configure the device, it is recommended to connect it to a computer via LAN-port No. 3.
router [email protected] 2804 v7 rev1 is a universal network equipment needed to connect end devices to the Internet and IP-TV via Ethernet cable, telephone line and wireless cellular communication via 3G/LTE modem.
And in this article, the setup of the Rostelecom fast 2804 v7 router is discussed in detail, as well as its main characteristics and the setup of the 3g modem.
By the way, the advantages of this router are that, at its relatively low cost, it supports almost all the functions necessary for an ordinary user: from setting up a print server to the possibility of reserving the main Internet channel.
Sagemcom [email protected] 2804 v7: Features
In addition to the standard possibilities for distributing Internet traffic and IP-TV between several functional nodes of the local network, the router [email protected] 2804 also supports additional features such as:
- - creation of a backup Internet channel (in case of a power outage or problems on the side of the main communication provider);
- - the ability to use the router as a print server (for connecting several user devices to a network printer);
- - the possibility of using [email protected] 2804 as a network drive (in other words, when connected to a hard drive router, it can be "used" as a miniature server).
On the front panel of the sadgemcom fast 2804 there is a block of indicators of the router:
1. Power indicator. The normal operation of the modem is indicated by the constant green color of the Power indicator.
If this LED is red, then the fast 2804 modem is in emergency recovery mode, which starts when the router software is slightly damaged.
2. DSL indicator, which with a constant green light notifies the user of a normal ADSL connection, and with frequent blinking, the establishment of this connection.
3. Internet indicator, which should be solid green if the connection through the Internet account is successful.
4. WLAN indicator, which lights up green when the wifi module is activated on the router.
5. Several ETH indicators that glow when external devices are connected to the corresponding Ethernet port via a network cable.
6. WPS indicator, green indicates successful connection to the user device via .
7. USB indicator indicating successful connection of external media to sagemcom fst 2804 v7.
On the back of the fast 2804 v7 rev1 are:
One ADSL port for connecting to the Internet via a telephone line;
4 LAN ports (for connecting to a router via twisted pair);
A small hole with a Reset button recessed in the case (to reset the router to factory settings, you must press this button with a paper clip or a needle and hold it for 10 - 15 seconds);
Power connector (to which the sagemcom f st 2804 v7 power supply is connected);
Power button;
On the right side panel of sajack fast 2804 are located:
Connecting sagemcom f st 2804 v7
When connecting to the Internet via an ADSL telephone line, the cable provided by the provider should be connected to the splitter input (LINE), and the telephone set and router should be connected to its PHONE and MODEM outputs, respectively.
When connecting to the Internet using WAN Ethernet technology, the provider's network cable must be connected to the first LAN connector of the SajemCom 2804 router.
Modem Rostelecom f st 2804 v7: setup instructions
If the computer (on which the Rostelecom fast 2804 v7 router will be configured) is correctly connected to the router via twisted pair, then the following indication should be present on the router:
The first indicator is solid green;
- the second indicator - slowly blinking green;
- the fourth indicator - lights up or blinks green;
- one of the LAN ports is lit or blinking green.
The setup of the Rostelecom fast 2804 v7 router described in this manual corresponds to the initial setup of the device. If the router was previously in operation, it is recommended to first reset the device to factory settings using the Reset button.
Setting up a Sadgemcom 2804 router using the hardware setup wizard
To launch the fast 2804 router setup wizard, insert the disk supplied with the device into the computer's CD drive and follow the program's further instructions.
When the software installation is complete, the Setup Wizard will automatically start (which can also be launched from the Start menu -> Programs -> Hardware Setup Wizard).
In the process of automatically configuring the Rostelecom fast 2804 router, the following operations are performed:
- - updating the router software from the installation disk;
- - selection of the desired router configuration;
- - configuration of PPPoE connection and 3G redundancy;
- - diagnostics of equipment performance;
- - Installing the latest firmware version of the router from the update server.
Manual configuration of the router Rostelecom fast 2804 v7
In the absence of an installation disk, it is recommended to configure the Wi-Fi router [email protected] 2804 manually. To do this, in the address bar of any Internet browser installed on your computer, enter the combination of numbers 192.168.1.1 (the static ip address of the device indicated on the service label on the back of the sagemcom 2804) and press the "Enter" key.
It is recommended to change the default authentication data (login / password) to unique ones later to protect your router from unauthorized access.
Initially, you will be taken to the page of basic technical information about the device.
Modem Rostelecom [email protected] 2804 v7: Ethernet connection instruction
1. To configure the fast 2804 v7 modem by Rostelecom, in the left vertical menu, select the "Additional settings" section:
Here, first delete all connections created by default in the “Wan service” subsection;
In the "Layer 2 interface" tab, delete "DSL ATM";
Go to the "ETH interface" tab: select "eth0/eth0" in the drop-down list, set "VLAN/MUX mode" in the connection mode and click the "Apply/Save" button.
2. When all unnecessary settings are “cleaned up”, return to the “Wan service” tab again, click the “Add” button and select the “eth0 / eth0” port set in the previous step. Click Next.
3. In the next window, select the type of service "PPPoE" and write the value "-1" in the two lower lines. Click "Next" 
4. At the next stage, in the "PPP username" and "PPP password" windows, enter the username and password for connecting to the Internet from your agreement with the provider. Click "Next"
5. If the new window contains the columns "Enable NAT" and "Enable Firewall", then put a marker in front of each of them. In subsequent windows (with the standard setup of the Rostelecom fast 2804 v7 router), nothing needs to be changed - click "Next" several times and at the end "Apply / Save" to make changes to the router settings.
How to set up a Rostelecom fast 2804 v7 router with an ADSL connection?
When connecting the Internet via a telephone line, after deleting the standard settings in the first step of the previous instruction, go to "Advanced settings", then "Layer 2 interface" and click the "Add" button.
- - in the VPI and VCI fields, enter the data from the contract with the provider (they can also be clarified in technical support) and click "Next";
- - go to "WAN service", click "Add" and select the interface according to the data entered in the previous window. Click next.
- - in "WAN Settings" select the type "router" and click "Next" again
- - enter the login, password and PPPoE service name from the Internet connection agreement;
- - set the marker on the fields "retry PPP on authentication failure" and "Enable IGMP Multicast Proxy", then double-click "Next" and "Apply".
sagemcom f st 2804 v7: wifi setup
Go to the "WLAN Settings" menu section;
- check the boxes "Enable wireless communication" and "Enable multicast transmission over wireless network (WMF)";
- enter "SSID" (this is the name of your Wi-Fi access point) and click "Apply";
- go to the "Security" section;
- Optionally, you can disable the WPS option;
- select the type of authentication "WPA-PSK";
- enter the password for Wi-Fi;
- select WPA encryption "TKIP+AES";
- click "Apply" to save the new settings.
Fast 2804 v7 router: setting up a 3g modem
Below is a sample list of supported sagemcom fast 2804 v7 rev 1 3G USB modems
- HUAWEI: E220, E1550, E1552, E1752, E160G, E176G, E180, E169G, E150, HW601
- ZTE: MF112, MF626, MF627, MF180, MF190A
- Alcatel: X220, X080
- Airplus: MCD-650
- Withtel: WMU-100A
- Anydata: ADU-300
- Yota: LU156 (LTE)
To set up a 3g modem on a fast 2804 v7 router:
Connect the device to a special USB connector on the side panel of the router;
Go to the "3G Configuration" section of the web interface and set the marker to "Enable 3G reservation";
With these settings, when the main (ADSL or Ethernet) Internet connection is disconnected, the router will automatically switch to the 3G/LTE channel.
This review will step by step review and describe the Sagemcom F ST 2804 V7 setup. This is an entry-level router, which is often sold in addition to the services provided by domestic providers. These include the nationwide MTS and Rostelecom. It is on the example of configuring the connection of such a router to the network equipment of the last company that this material will be presented.
Network Gateway Package
Standard and typical delivery list for this router. Separately, it should be noted that such a network gateway is tied to the equipment of a particular provider. That is, if the router is designed to work in combination with the software and hardware of the Rostelecom company, then it will only work in such a bundle.
The delivery list includes a Sagemcom F ST 2804 V7 router. Setting up a Rostelecom connection is described in detail in the instruction manual. The manufacturer did not forget to include a warranty card in the package, the validity of which is 1 year. This is a complete list of the configuration of this solution. This list is supplemented by a power supply with a 0.5 A output and an interface cord, which is mainly used at the stage of setting up a network connection.
Also in the delivery list there is a CD with specialized software. By default, the hero of this article has the V5 software version, which cannot work normally with Rostelecom equipment. Therefore, it is necessary to upgrade the router considered in this material to version V7.
Main settings
The main parameters of this router are as follows:
- Three possible ways to connect to the Internet: Ethernet, ADSL and 2G / 3G (in the latter case, you must additionally purchase an external modem and a starter pack to be able to connect to a cellular network).
- Four RJ-45 ports, which can be used both for connecting computing devices via twisted pair to the global web, and switching set-top boxes.
- One USB standard port, which is used to connect a modem.
- A wireless network based on a Wi-Fi transmitter, within which information can be transmitted at speeds up to 300 Mbps.
The body of this device is plastic. May be white or black. Information LEDs are displayed on one side of it. The first of them indicates the presence of power, the second indicates an active ADSL connection, the third indicates the presence of receiving information from the Internet. The next information indicator indicates the operation of the wireless network. Then there are four LEDs that characterize the functioning of the wired segment of the internal computer network. The last light element in this case shows the operation of the USB port built into the router.
On the top side of the device are a USB connector and two buttons. One of them includes a network gateway of this model, and the second uses the technology of automatically connecting the device using Wi-Fi.
On the opposite side face from the information panel, all connection ports are displayed. These include an ADSL connector, a USB port, and 4 RJ-45 ports. There is also a power socket here. There is also a button to reset the software to its original state.
Connection
At the first stage, setting up the Sagemcom F ST 2804 V7 comes down to making the following connections:
- We install the router at the place of use. The latter must meet the following requirements: there must be an outlet as close as possible, an ADSL input wire and interface cords from computers must be connected.
- Next, connect the power supply.
- Then it is necessary to carry out switching with the equipment of the ADSL provider.
- The last stage is the collection of the wired part of the computer network.
Setting up an external wired connection
At the first stage, you need to update the software shell of the router. To do this, on the PC connected to the network gateway, launch the CD and in the autorun window that opens, select the “Update router” item and wait for this operation to complete.
Then setting up the Sagemcom F ST 2804 V7 comes down to configuring the external connection. To do this, we re-initialize the launch of the CD and select the “Full Setup” item in its menu. In the future, follow the instructions of the wizard and set the connection parameters, which can be taken from the contract with the provider for the provision of services. At the end, save the entered data and exit the setup wizard.
Modem setup
The next step is to configure the Sagemcom F ST 2804 V7 modem, which is used to implement a backup method for connecting to the Internet. It consists of the following actions:
- Choose a supported 3G modem model, purchase it along with the starter pack. We collect everything together and connect to the router.
- We launch any available browser on a PC that is directly connected to the network gateway.
- In its address bar, enter the device address in the format 192.168.1.1.
- Next, in the request window in the fields "Login" and "Password" you must enter admin. After that, press the "Login" button.
- Go to "Advanced Settings" and select the "3G Configuration" sub-item.
- Then we set the PIN code for the installed SIM card.
- We save the data and exit the program shell.
Setting up an internal connection
The wired connection is automatically configured, and there is no need to perform any additional manipulations with the Sagemcom F ST 2804 V7 program parameters. Wi-Fi setup is also automatic. The only thing you will definitely need is to rewrite the network name and password to connect to it from the bottom cover of the device case. In the future, simply enter them in the appropriate request.
IPTV
The router in question supports IPTV technology, with which you can watch television programs. In this case, the step-by-step configuration of the Sagemcom F ST 2804 V7 router is performed as follows:
- We go into the router settings menu according to the previously given method.
- After opening the settings interface, you need to go to the sub-item "Advanced Settings". Then you need to select "Interface grouping".
- At the next stage, click the "Add" button and set the connection port of the IPTV set-top box.
- Save the settings and exit the setup interface.
Price
At the moment, such a router can be purchased for 1200-1500 rubles. Again, it is advisable to purchase such a solution only if Rostelecom acts as a provider of Internet traffic. Given the functionality of the device in question, such a cost is fully justified.
Conclusion
Sagemcom F St 2804 V7 is a very high-quality, functional and at the same time very affordable network gateway. Setting it up is a fairly simple operation, and every user is able to handle it. The provider at the same time simplified the process of its implementation as much as possible. Therefore, such a router is simply ideal for creating home computer networks.
Many owners of the Rostelecom Sagemcom f st 2804 v7 router prefer to configure the Internet and IP-TV on their own, since modern firmware versions allow even an ordinary user to do this. If you also wondered how the Rostelecom fast 2804 v7 router is configured, then this article is for you. In it, we will analyze in detail the process of setting up the connection itself and the parameters of the future wireless network.
Router preparation
First of all, we need to correctly connect the Rostelecom router Sagemcom f st 2804 v7. To do this, connect the power cord to the rear panel. Then, if a telephone connection is used, insert the Internet cable into the first slot. If your home has fiber or any other connection that uses a standard Ethernet cable, insert it into the first of the following four ports.
After that, we turn the router to the front side and look at the lights on:
- "Power" - lights up in any case if the router is connected to the network;
- "DSL-link" - shows us that the Rostelecom fast 2804 router receives a signal from the provider's servers, so it should be on;
- "WiFi" - by default, it is enabled immediately in all Rostelecom modems;
- "LAN" - lights up if the cable is connected correctly.
Important: as you understand, even at factory settings, the router can “distribute” a WiFi signal. So there is no need to configure it separately. But, if you want to change the network name or the set password, you can find instructions for this later in the article.
I would also like to note that during the setup of the Rostelecom f st 2804 v7 router, you may have a question: what is this usb port on the back of the case? Answer: This is a standard usb for connecting your portable Internet (connect) in case of a disconnection with the main provider or the need to use this type of repeater on several devices at once.
Setting up a Rostelecom fast 2804 v7 router
The first stage of setup is the entrance to the main interface. It is carried out through the browser:
- we launch a convenient Internet browser for you;
- in the address bar, enter the ip of your router: 192.168.1.1;
- in the Login and Password fields, enter the keyword "admin" in lower case.
If everything is done correctly, you will be transferred to a new page in the same tab, where the main menu will be placed on the left on a blue background. We will work with him.
Reset basic settings
If you are setting up a Rostelecom fast 2804 router that has already been used elsewhere or due to lost settings, then all settings must be returned to factory settings. You can do this in the following way:
- go to the last menu item "Management";
- open the first subsection "Settings";
- find and click on the submenu item "Reset";
- in the middle of the page we see the button "Restore default settings";
- click on it;
- click OK in the pop-up confirmation window;
- we wait until the reset operation is completed, and we will again be moved to the main page of the web interface.
All is ready! Now the Rostelecom fast 2804 v7 router can be configured.
Removing unnecessary factory connections
Since after resetting all the parameters, the router creates several initial non-working connections, the first step is to delete them so that there are no errors during operation. This is done in several steps.
- in the main menu on the left we find "Additional settings";
- in the pop-up submenu, open "WAN service";
- in the updated window we see a table of three items (three connections), on the left side of which there is a “Delete” column, check the boxes everywhere;
- under the table we find the button "Delete", click on it;
- in the updated window we see an empty table.
- all in the same place in the "Advanced settings" open the item "Second-level interface";
- the first section of the submenu is "ATM PVC interface";
- delete the only table item in the same way as in the previous step;
- waiting for page update;
- open the last item of the pop-up submenu - "ETH Interface";
- delete the row in the table in the same way;
- we observe a page reload and the disappearance of the remote configuration;
Direct setup by Rostelecom Sagemcom f st 2804
After the cleaning is completed, a deep configuration of the Rostelecom fast 2804 router is performed:
- we return to the “ATM PVC Interface” and click on the “Add” button;
- on the page that opens, indicate the data of the Internet connection: VCI and VPI;
- all other points are left unchanged;
- scroll down the page - the button "Apply / Save";
- in the same way, we add a connection for IP-TV by clicking on "Add" (only VCI will change, in most cases).
The Rostelecom f st 2804 v7 router is connected on the WAN service tab:
- click "Add";
- select the created configuration - "Next";
- specify the type of service used (in most cases PPPoE);
- on the page that opens, enter the user data (login / password) specified in the agreement on the provision of services on the Internet;
- in the same place, select the desired name for the connection (“PPPoE service name”);
- we check the presence of a checkmark in front of the item "repeat PPP ...";
- click "Next";
- move the "ppp1" route you created to the left column if it's in the right column. then we move the connection via usb in the opposite direction;
- we perform the same operation and again "Next".
We see the list of final settings and make sure that in the second line opposite "NAT" the "Enabled" parameter is indicated. If this is not the case, we return to the stage of specifying the login and password for the connection and set the checkboxes on this page to include NAT and Firewall. Apply the changes made.
How to set up a fast 2804 v7 Rostelecom router for IP-TV? Very simple! We repeat the first three points from the algorithm above, only select the second created configuration (in the second step) and the Bridge connection type instead of PPPoE (in the third). Go ahead, save the settings and voila! Internet is!
How to connect a router Rostelecom f st 2804 to WiFi
The firmware of the router Rostelecom f st 2804 v7 implies the initial settings for a wireless connection. To change them, you need to do the following operations:
- main menu item "WLAN settings";
- go to the "Basic" submenu;
- check the box to enable wireless communication;
- change the SSID to any network name you like and save the changes;
- go to the "Security" submenu;
- disable WPS (weak point of the wireless connection, which can be easily hacked);
- we check that our network name is selected and change the standard password to the one we invented (the field after the "Authentication" item);
- save the changes made.
That's all, we figured out how the Rostelecom router Sagemcom f st 2804 is configured on its own.
Summarizing the above material, we can say that connecting a router to the Internet comes down to four steps:
- reset;
- removal of standard connections;
- creation of a new PPPoE port;
- changing WiFi settings.
Having mastered these steps, you yourself will be able to configure and tell others how to connect the Rostelecom f st 2804 router to the network.
Important: the VPI and VCI values mentioned in the article are unique for each region of Russia. Therefore, they must first be clarified with the provider, or found on the Internet.
The entire algorithm described above is clearly demonstrated in this video:
What other questions did you have during the setup?